Introduction to Stone Processing Technology

Introduction to Stone Processing Technology

2025-04-18 10:28:35 admin

Diamond Tools manufacture

Processing Process

1. Mining

The first step in stone processing is mining, which is to extract stone from a quarry. There are two main methods of mining: manual mining and blasting mining.

  • Hand quarrying: This traditional method involves using hand tools to remove stone from a quarry. Although it is very labor intensive, it allows for greater control over the quality of the stone being mined. Hand quarrying is often used for softer stones such as marble, where precision is critical.

  • Explosive mining: This method uses explosives to break up large pieces of stone. Explosive mining can be further divided into two categories: micro-blasting and mass blasting. Micro-blasting is easier to control and can minimize damage to the stone, while mass blasting usually results in lower utilization rates because a large amount of stone may be broken during the mining process. Mass blasting is usually avoided unless the stone is particularly hard and needs to be mined with mass blasting due to the large amount of waste it may cause.

2. Sawing (rough material processing)

Once the stone is mined, it is usually processed into slabs, forming rough blocks. The sawing process is essential to shaping the stone into a usable shape.

Diamond circular saw: The most common stone sawing equipment is the diamond circular saw. This saw uses a large disc-shaped saw blade that is inlaid with diamond particles that are bonded together using a powder metallurgy process. Diamond saws are particularly suitable for processing super-hard stones such as granite and marble due to their durability and cutting efficiency.

Sawing technology:

  • Single blade: Cuts the stone using a single large disc with a diameter twice the stone height plus the flange diameter. This configuration can be challenging for processing large slabs.

  • Multiple blade configuration: A row of multiple parallel saw blades enables the saw to cut a whole piece of wood into multiple boards at the same time. This method is efficient and can shorten processing time.

Limitations:

While diamond saws are effective on softer stones such as marble, they are not suitable for harder granite due to the abrasive nature of diamond. Also, using a diamond saw can result in a lot of waste if flaws in the stone are not discovered before machining, as the entire stone may be scrapped if flaws are discovered after machining.

Main processing equipment:

  • Large automatic granite sanding saw

  • Multi-blade bidirectional cutting machine

  • Multi-blade computer controlled granite cutting machine

  • Granite circular saw

The boards produced by this sawing process are called rough boards and require further processing to achieve the desired surface effect.

3. Grinding and polishing

The grinding and polishing stages are crucial for finishing the rough sawn boards to ensure that their thickness, flatness and gloss meet industry standards. The process consists of the following steps:

  • Rough grinding and flattening: The first step in this phase is rough grinding, which aims to remove any unevenness on the surface of the blank. This is usually done using a diamond flattening machine or a bridge grinder. The goal is to create a flat surface that will be the basis for subsequent polishing.

  • Semi-finish grinding: Once a flat surface is achieved, the next step is semi-finish grinding. This process further smoothes the surface in preparation for fine grinding. At this stage, finer diamond polishing pads are used to improve the surface quality.

  • Fine grinding: Fine grinding is based on semi-fine grinding and requires the use of finer abrasives to obtain a smooth and uniform surface. This step is essential for preparing the stone for the final polishing stage.

  • Polishing: Polishing is the final step in the process and is intended to enhance the gloss and overall appearance of the stone. Diamond polishing pads are often used for polishing as they are effective in bringing out the color and texture of the granite or marble. The polishing process not only enhances the aesthetics but also adds a layer of protection to the stone.

Main processing equipment:

  • Automatic multi-head continuous grinding machines: These machines can efficiently process multiple slabs simultaneously.

  • Diamond leveling machine: used for preliminary leveling and rough grinding.

  • Bridge type grinder: Suitable for larger slabs, providing precision and control.

  • Disc grinder: For fine grinding and polishing.

  • Reverse rough grinder: For efficient and fast material removal.

  • Handheld grinder: For fine work and finishing touches.

4. Cutting

After the grinding and polishing process is completed, the next step is cutting. This stage requires the use of a special cutting machine to cut the polished plate into the required specifications and sizes.

  • Cutting technology: The cutting process can be carried out using a variety of machines, each designed for a specific cutting task:

  • Longitudinal multi-blade cutting machines: These machines are used to cut the panels longitudinally, thus making it possible to produce multiple panels from one panel.

  • Crosscutters: Ideal for crosscutting sheets into smaller sections.

  • Bridge cutters: These machines allow for precision cutting of larger sheets to exact dimensions.

  • Cantilever cutter: For cutting thicker materials, providing stability and control.

  • Hand crank cutting machines: While less common in modern machining, these machines are still used for smaller operations or specific tasks.

  • Final product: After cutting, the sheets are trimmed to the required size and specifications for sale or further processing. This step is critical to ensure that the final product meets customer requirements and industry standards.


Awesome Image

Xiamen ZL DIAMOND TECHNOLOGY CO.,LTD. is a New Three Board listed enterprise, engaged in the development and application of diamond new material.

  • ZL-FHP Diamond hand polishing pads
    ... 2026-06-11 09:18:55

Feedback

Tel
E-mail
Map